|
|
Post by Jaroslaw on Nov 26, 2021 9:22:54 GMT
Hello everyone. Looking for okoume plywood. I want to start construction in April in Poland. Are there people here who would give me a reference to the company producing okoume slices, as close to Poland as possible? Because it's about transportation. Of course I will need a certificate. Please note that I do not want to build with the CNC Kit.
And one more question; Will the sailboat be certified when building without the CNC Kit?
Thank you Jaroslaw
|
|
brucel
Junior Member
Posts: 54
|
Post by brucel on Nov 26, 2021 14:53:38 GMT
Hi Jaroslaw, I can not help with the plywood front. Trekka Plywood came from Spain. As far as building by the plan without CNC kit, 100% you can build it to class certification. There is nothing in the class requirements that says you need to build with a CNC kit, it is just for some of us it is dollars/euro vs time vs skill consideration. Download the documents on this page, these documents are in my opinion the most important on the site if you want to end up with a class certified boat. www.classglobe580.com/class-registration/ Good luck. bruce |
|
|
|
Post by Jaroslaw on Nov 26, 2021 18:23:04 GMT
I have ordered the material: pine wood and oak. I just need plywood. Thanks for telling me I can build without CNC kit.
Thanks you for the answer Bruce
|
|
|
|
Post by Renaud hull 28 on Nov 28, 2021 8:01:16 GMT
Hello
mine come from
Iryna Karan
International Sales account
Nord Compensati
+39039243132202
i.karan@nordcompensati.com
nordcompensati.com
via Torricelli, 44, 20851 Lissone (MB), Italy
|
|
|
|
Post by thomas on Nov 29, 2021 9:14:28 GMT
Hello mine come from Iryna Karan International Sales account Nord Compensati +39039243132202 i.karan@nordcompensati.com nordcompensati.com via Torricelli, 44, 20851 Lissone (MB), Italy Mine too. Very friendly contact and good material, recommendable. Don`s boat (Trekka) was also built with this plywood in poland by this company nordcompensati. So certification and transportation shouldn't be a problem. Good luck and have fun. |
|
|
|
Post by Jaroslaw on Nov 30, 2021 9:09:35 GMT
Hello Iryna Karan.
Write me here the technical specification of okoume plywood that you have. Let someone on the forum tell me if the plywood data required for certification by 5.80ClassGlobe will be accepted.
Need:
a) Waterproof MARINE plywood 8mm on deck, cockpit, bulkheads and built-in interiors, 11 sheets (1.22m x 2.44m)
b) Waterproof MARINE plywood 5 - 6 mm for cabinets etc. 1 sheet (1.22m x 2.44m)
c) Waterproof MARINE plywood 10mm for the bottom, side and transom plating 12 sheets (1.22m x 2.44m)
I will need to send me this plywood to Poland to the following address: rgion, podlaskie voivodeship.
Write me how long I have to wait for the plywood
Regards Jaroslaw
|
|
|
|
Post by thomas on Dec 4, 2021 8:15:43 GMT
Hi Jaroslaw, unfortunately, I can`t tell you whether the quantities are sufficient, as I am not finished with my construction yet. As far as I know, these are the minimum plywood requirements. To be on the safe side, I ordered 2 more sheets of each strength. Remember if you make a mistake while cutting you have a problem because there is no material left f you have to redo a step while building. Some information about my plywood purchase is on my blog: minisailer.ch/?p=92 |
|
|
|
Post by Jaroslaw on Dec 12, 2021 17:45:37 GMT
Hello everyone. Looking for okoume plywood. I want to start construction in April in Poland. Are there people here who would give me a reference to the company producing okoume slices, as close to Poland as possible? Because it's about transportation. Of course I will need a certificate. Please note that I do not want to build with the CNC Kit. And one more question; Will the sailboat be certified when building without the CNC Kit? Thank you Jaroslaw R |
|
|
|
Post by Jaroslaw on Dec 12, 2021 17:53:37 GMT
Hi Thomas. Nice blog minisailer.ch/?p=92 Could you please give me a contact, the company where you bought okoume plywood. E-mail adress. Regards Jaroslaw |
|
|
|
Post by thomas on Dec 14, 2021 12:57:46 GMT
Hi Thomas. Nice blog minisailer.ch/?p=92 Could you please give me a contact, the company where you bought okoume plywood. E-mail adress. Regards Jaroslaw It`s the same contact like Renaud wrote: Iryna Karan International Sales account Nord Compensati +39039243132202 i.karan@nordcompensati.com nordcompensati.com via Torricelli, 44, 20851 Lissone (MB), Italy You can refer to my name Thomas Kindermann from Switzerland. See here for further more: nordcompensati.com/en/compensati/compensato-marino-okoume-rina/Happy building :-) |
|
